Ecobee turn fan on

Mar 31, 2022 ... How to change your mode on the Ecobee thermostat.

Here’s how to enable Auto Mode: Go to Main Menu > Settings > Installation Settings > Thresholds > Auto Heat/Cool and select Enable. Once the Auto Mode is activated, go to Main Menu > System > HVAC. With this mode, the Ecobee will turn off the AC when the temperature goes above the blue cooling set point.Check if the breaker in your home's breaker box is flipped for the heater, air conditioner, or other device you're having problems with. Flip the breaker back on. Wait at your breaker box for 30 seconds, to make sure it does not flip back quickly. Allow your thermostat an additional minute to finish starting back up.Cannot turn on Fan Only mode. Problem. My Ecobee4 can turn on the fan when heating but not when I select Quick Setting -> fan on. It says Fan on and holding but nothing happens. I saw some earlier posts saying you need a green wire which I have. I also checked all wire connections and they look good.On the main screen hit the little cog wheel on the bottom right. Then set the fan to on instead of auto. If that still doesn't work you either don't have it wired up to have that option or that's why your system iced up (I'm assuming) because of no airflow over the evaporator coil. 1. Reply.Turn it off, wait at least one minute, then turn it back on again. Allow your Ecobee to boot up as normal. Once the thermostat has booted up, open the Quick Change menu (cog icon) and check the Wi-Fi connection icon. If it isn’t connected yet, try closing the menu, waiting a few more minutes, and then opening again.Your Ecobee furnace isn’t turning off because your fan limit switch isn’t configured or is faulty, or there are problems with the thermostat. Fix the problem by setting the fan limit switch to auto or replace it if broken, and ensure your thermostat is working by checking the wiring and batteries. If you can’t seem to get your Ecobee ...Aug 27, 2022 ... ... Ecobee3 Lite Smart Thermostat- https://amzn.to/3PMNthh Ecobee Smart Thermostat Enhanced Works with Alexa- https://amzn.to/3bndLr9 Ecobee ...Turn it off, wait at least one minute, then turn it back on again. Allow your Ecobee to boot up as normal. Once the thermostat has booted up, open the Quick Change menu (cog icon) and check the Wi-Fi connection icon. If it isn’t connected yet, try closing the menu, waiting a few more minutes, and then opening again.

Change Your Fan Control. During the time you are setting up your thermostat device, you will have the option to adjust fan control. The default settings will adjust your fan for energy efficiency. We have seen cases where the fan control needs to be changed as their Ecobee is not able to tell the furnace to turn on the heat. The unit shows Equipment running now Fan, but it never runs. Builder is avoiding question, wonder if something is wrong. On main screen, hit lower right icon, and tap fan from auto to on. Make sure to cancel it when you’re done otherwise it won’t auto turn off. Run fan only. I have a ecobee3, basic furnace with no a/c. I want to use the fan to cycle air through the house. I go to quick settings and choose set fan to on. I have also set minimum run time to 10 minutes. Nothing happens, it says no equipment running.As the title states I just got this thermostat and I’m at a loss on how to remotely turn on the fan only mode. Basically, I was hoping to use the smart sensor to trigger a HomeKit automation to circulate the air (cooling more won’t help) but I only see options to turn it to heat, cool, or auto. ... Increase ecobee fan. {{ ((( states.sensor ...Installing your ecobee Thermostat. In most homes, installing an ecobee thermostat is an easy DIY project that takes about 20-30 minutes to complete. The installation guide includes step-by-step instructions that make it easy to install and wire your thermostat, so use it as your main reference. You can also refer to this page for extra help.Click Settings > Preferences > Hold Action, then choose Until the next scheduled activity. Now close the Settings window. You can also do this on the Ecobee itself by selecting Main Menu ...

Installing your ecobee Thermostat. In most homes, installing an ecobee thermostat is an easy DIY project that takes about 20-30 minutes to complete. The installation guide includes step-by-step instructions that make it easy to install and wire your thermostat, so use it as your main reference. You can also refer to this page for extra help.To enable Airplay. Open the Home app, select your thermostat > Scroll to AirPlay Speaker (Beta) and toggle on Listen for “Hey Siri”. Good to know: You can also use multiroom audio with AirPlay by selecting multiple speakers or TVs on your iPhone or iPad’s AirPlay Audio Controls menu.In order to configure your ecobee for multi-speed fan support, you'll need to select " I'm an ecobee Pro " during the initial equipment configuration screen. On the thermostat. Go to the Main Menu > General > Settings > Installation Settings > Equipment > Reconfigure Equipment, then I’m an ecobee Pro. Go to Next.On the main screen hit the little cog wheel on the bottom right. Then set the fan to on instead of auto. If that still doesn't work you either don't have it wired up to have that option or that's why your system iced up (I'm assuming) because of no airflow over the evaporator coil. 1. Reply.On the thermostat: Go to the Main Menu > General > Comfort Settings , then remove the ecobee thermostat from participating in all of your Comfort Settings. On the ecobee app: Tap Home > Tap on the Thermostat > Menu > Comfort Settings , then remove the thermostat from participating in all of your Comfort Settings.To fix the issue of AC mode adjustment, follow the below mentioned steps. STEPS TO FOLLOW: STEP 1 – Open the Ecobee home app. STEP 2 – Tap on the horizontal lines which are present on the top left corner. STEP 3 – Choose “Set Thermostat” option. STEP 4 – Now navigate towards “Change Settings”.

Dale heisch attorney.

If eco+ is disabled for the day, the Adjust the Temperature for Humidity feature will not be activated until midnight. Enable Adjust for humidity. To use Adjust for Humidity, you can enable it directly through the ecobee app. On the ecobee app. Tap the thermostat > Menu > eco+ > Adjust temperature for humidity, then enable using the toggle switch.Basically, the flame heats up that little metal rod and it tells the furnace that the flame is on, and therefore can fire everything up. If it doesnt sense the flame, it thinks it's not lit and is just pumping gas out, so it kills the gas. It should be 1 1/4 or 5/16 screw holding it in. It has 1 wore going to it, connected with a spade connector.If I want my fan to run 20 minutes per hour, the ecobee will run the fan every few minutes for only a very few short minutes, resulting in the fan turning off and on constantly. ... I want the fan to run for 20 mins straight then turn off for 40 mins. Share Add a Comment. Sort by: Best. Open comment sort options. Best. Top. New ...Sometimes I just like to run the fan when the house feels stagnant or too humid in one area. So it's never at a particular time of day or daily. I just have to manually turn the fan on and remember to turn it off. Nest did have this function, it would show up when you told the system to run the fan, it'd ask for how long.If Configure Staging is set to Automatically. When your thermostat's Configure Staging setting is set to Automatically, you can adjust the Aux Savings Optimization value to lower aux heat usage. 2°F / 1.1°C - sacrifice savings for comfort. 2°F / 1.1°C - sacrifice savings for comfort. 2.3°F / 1.3°C - sacrifice a bit of savings for comfort.

When the furnace is on, hot air blows, but when The desired temperature is reached the furnace shuts off, but the fan keeps blowing, pushing cold air around. Edit: when the thermostat is active (flame turns red) the fan turns off, until the thermostat is heated, then it turns on again. It actually seems to work properly at this point.Hi All, I am new to the automation/scripting stuff here and was trying to figure out how to get my Ecobee to turn on my HVAC fan when there is a temperature differential between two of its sensors. I tried looking through the scripting help but I’m struggling to piece it all together. So far I figured out how to pull in the sensor data for one sensor but …On the main screen hit the little cog wheel on the bottom right. Then set the fan to on instead of auto. If that still doesn't work you either don't have it wired up to have that option or that's why your system iced up (I'm assuming) because …Mar 21, 2018 ... Comments8 · How To Voice Control On Ecobee4 Pro (3 of 13) · How to Use The Ecobee4 Pro Smart Thermostat · Ecobee3 Lite Manual | How To Use Eco...Ex: Hey Siri, Turn on the ecobee fan. It stops the current schedule, runs the fan immediately for the specified amount of time (based on per hour setting) BUT runs it consecutively over the next hour instead of breaking it up then switches back to the proper schedule / fan setting at the end of the hour. 2. Optional Smart Fan control would be nice.Your ecobee thermostat's schedule is made up of Activities and Comfort Settings. Activities determine the time and length of a Comfort Setting, and the Comfort Setting determines the temperature setpoints and fan behaviour your ecobee will follow during the activity. The ecobee comes with three default Comfort Settings Home, Away and Sleep. Wait for it to cool down, and set the temperature lower. If this is a consistent problem, it indicates there is a deeper problem with your furnace, and will need to be serviced by an HVAC technician. 4. Check Furnace Fuse. There is a small fuse on your furnace to protect the electronics from surges. The unit shows Equipment running now Fan, but it never runs. Builder is avoiding question, wonder if something is wrong. On main screen, hit lower right icon, and tap fan from auto to on. Make sure to cancel it when you’re done otherwise it won’t auto turn off.Here’s how to add the ecobee app widget: 1. On your phone’s Home Screen, touch and hold an empty area of the screen until the apps jiggle. 2. Tap the Plus icon in the upper-left corner. 3. Scroll down and select the ecobee widget. 4. Scroll left and right to see the different options. 5. When you see the widget you want, select Add widget. 6.In order to control a Hampton Bay ceiling fan with an iPhone, owners must install a Bluetooth receiver that installs inside the fan. Once he installs the receiver, the user pairs i...Check the wiring at your ecobee. 2. Check the wiring at your furnace/air handler. 3. Check the equipment configuration on your thermostat. 4. Check your threshold settings. If you've followed all of the troubleshooting steps above and your air conditioner still isn't turning on, please contact Customer Support for further assistance.When set to "thermostat", the ecobee will operate your system fan differently than your furnace during heating cycles by sending the signal to run the fan itself rather than relying on the furnace to do so. To adjust this setting, go to MAIN MENU > SETTINGS > INSTALLATION SETTINGS > EQUIPMENT > FURNACE > FAN CONTROL IN HEAT …

After you set up the ecobee, you need to go through an equipment setup to confirm the correct wiring and equipment is linked to the ecobee. One of those settings is the control for the fan, the default setting is for the ecobee to control the fan for energy efficiency. This was to much for my ecobee to control and was not able to tell the ...

Here are the primary reasons ecobee won’t turn on your AC: Drain clog from the condensation operation of your HVAC. Low on refrigerant. The AC air filters could be blocked. The AC’s capacitor may be no longer functional. A dormant fan. Your ecobee thermostat may further be dysfunctional.Ecobee 4 Fans Turn on AC Doesn't - Help! Let me start off by getting a few things out of the way: -My old thermostat works fine, each unsuccessful attempt for the ecobee I'm putting the old one back and my air works perfectly, so it appears I don't have a technical issue ... Yes joining the 4 wires on the left of the ecobee should engage Fan ...Each setting is designed for different times and activities. For example, when you're at home, your ecobee thermostat can turn on the heat if it gets colder than 70°F (21°C) or activate the cooling if it gets warmer than 78°F (25°C). ... On the ecobee app. Tap the Thermostat > tap on the Menu > Sensors > select a Sensor > Participation ...Nov 26, 2021 ... 4:14. Go to channel · Furnace Not Turning on? Try This First! Don't Call an HVAC Tech Before You Try This! Myks Garage•170K views · 11:23.Sep 18, 2021 · graybeard (Bob M) September 18, 2021, 11:47pm 1. I have my Ecobee 3 integrated with HA and would like to use HA to have the furnace fan turn on every hour for 15 minutes between the hours of 3 pm to 11pm. I found the service climate.set_fan_mode can be set to on or auto so I set up a test pair of automations to turn the fan on at 16:00 and back ... If your Ecobee in not turning on the fan check that the wires are correctly connected and snug, check the Ecobee settings that control when the fan runs, and check the continuity of wires running between the furnace and …Here’s what you need to do to fix a blown fuse: Cut power to your furnace at the breaker switch. Open up the fuse box. You may need to use a screwdriver. Check the fuse. If the fuse is blown, the wire inside will be broken. If the wire is still intact, the fuse should work normally. If the fuse is blown, replace it.EcoBee has contacts labeled acc+ and acc- that can be set up to do a wide variety of functions. For this typical dehumidification function using the system, you would select Menu > Installation Settings > Dehumidifier > 1 Wire ACC+ > Open contact state to activate the dehumidifier. This setup uses 24V power from the R terminal to energize the ...

Money land 2 abcya.

Crossbreed liberty band.

Step 1: Check to see if the device is switched on and connected. One might not know that the heater (gas and electrical) has a power button. Ensure that the controller is switched on. Also, ensure the breaker that gives electricity to the heating unit is in the “On” condition within the electric board.Aug 7, 2023 · That way you are telling Ecobee that there is a wire in W1 when in fact there is none. Then switch Stage 2 delta temperature to 1F. Read also: How to set ecobee thermostat. Furnace fails to ignite. Your Ecobee wont turn on heat if your furnace fails to ignite. Go down to the furnace and check through the little glass if there is light linking. During setup, the ecobee thermostat will ask for the relay state information for your dehumidifier. The relay will be either open or closed. This information can be found in your dehumidifier owner's manual. Edit your dehumidifier’s settings on thermostat. Go to Main Menu > General > Settings > Installation Settings > Equipment > Dehumidifier ecobee optimize Turn this option ON to tell the thermostat to automatically set your heat temperature, cool temperature, system mode and furnace fan settings to maximize energy conservation while you are away. Turn this option OFF to manually configure Heat Temperature, Cool Temperature and Fan settings. Heat TemperatureNov 25, 2021 · Configure the HEAT DISSIPATION setting to the amount of time you want your fan to run after your HVAC setup has turned itself off. Remember to let it run for at least 30 seconds to guarantee that the excess heat generated by your climate control unit is pushed out of the home rather than funneled into your living spaces. One called “Air Mover On” sets “Fan Target Power State” to on. The other, “Air Mover Off”, sets “Fan Target Power State” to auto so the thermostat can take control back of the fan. Once these are created I can tell Siri “Air Mover on/off” and also utilize those scenes within automations to also control the fan. 1. Reply.Sep 15, 2017 · Here are some examples you might consider using with your own Ecobee: "Alexa, ask Ecobee to set the thermostat to home mode." "Alexa, ask Ecobee to resume the schedule." or ""Alexa, ask Ecobee to cancel hold." "Alexa, ask Ecobee if the heating is enabled." "Alexa, ask Ecobee if the dehumidifier is running." "Alexa, ask Ecobee to turn the fan on." Free Cooling Max Outdoor Humidity : This prevents Free Cooling from running when the outdoor humidity is too high. By default, this option is disabled. If you set this to Auto, your thermostat will determine the maximum allowed humidity level based on the temperature. Indoor/Outdoor Temperature Delta : The difference between indoor and outdoor ...Hello, I am trying to turn Z-Wave plugs based on the current state of a thermostat/climate entity. In particular my climate entity is an ecobee4 smart thermostat with a working integration - using the climate dashboard, I can control this thermostat and see its current state represented. Here is the YAML I have written. However, when the heater … ….

The Home+ app allows you to change the fan state between on and auto. This state change can only be made using scenes within the Home+ app. Once the scene is create in the Home+ app it can be activated within HomeKit itself. Using the DummySwitch plugin you can create a switch that enables the HVAC Fan on scene when flipped on and enables an ... Your Ecobee thermostat fan keeps running because of an issue in the settings. There are a few possibilities: the fan is in ‘On’ mode instead of ‘Auto’ mode, the smart recovery setting is on, or the heat dissipation time is over thirty seconds. These three setting errors are usually the cause of a continually running fan.Sep 15, 2017 · Here are some examples you might consider using with your own Ecobee: "Alexa, ask Ecobee to set the thermostat to home mode." "Alexa, ask Ecobee to resume the schedule." or ""Alexa, ask Ecobee to cancel hold." "Alexa, ask Ecobee if the heating is enabled." "Alexa, ask Ecobee if the dehumidifier is running." "Alexa, ask Ecobee to turn the fan on." Apr 16, 2024 · Here’s how it works: From the main display, open the Menu and select “Settings.”. Select the “System” option at the top of the list. Tap “ Fan .”. Use the scrolling selector to choose the length of time you want the fan to run. Your Ecobee Thermostat will confirm when it will turn off. Dehumidifiers. During setup, the ecobee will request the relay state (open or closed) of your dehumidifier, which can be found in your dehumidifier owner's manual. On the thermostat. Go to Main Menu > General > Settings > Installation Settings > Equipment, then Dehumidifier. On the ecobee Thermostat. Go to Main Menu > General > Preferences > Select Cooling Smart Recovery or Heating Smart Recovery, then Enable or Disable. How can I confirm that Smart Recovery is running? Your ecobee shows either a Blue snowflake or Blue perimeter line for cooling and an Orange flame or Orange perimeter line for heating. When Smart ... On the ecobee Thermostat. Go to Main Menu > General > Preferences > Select Cooling Smart Recovery or Heating Smart Recovery, then Enable or Disable. How can I confirm that Smart Recovery is running? Your ecobee shows either a Blue snowflake or Blue perimeter line for cooling and an Orange flame or Orange perimeter line for heating. When Smart ... On the thermostat: Go to the Main Menu > General > Settings > Installation Settings > Thresholds > Auto Heat/Cool, then select Enable. Once it is enabled, you can activate Auto mode by navigating back to the Home screen and selecting the System mode icon above the temperature. You can also activate Auto mode by performing the same action from ... "Hey Google, turn off the <thermostat name> hold." "Ok Google, turn on the <thermostat name> schedule." Fan Control: "Ok Google, turn the <thermostat name> fan on." Note: If this returns an error, try "Ok Google, turn the <thermostat name> blower on." System Mode: "Ok Google, set the <thermostat name> to heat."If Y1 is not highlighted, select the “No” option on the bottom left because this wiring is not correct. You will then be prompted to modify the selected wires. Manually add the Y1 terminal so that it’s highlighted. Click “Next” and follow the rest of the on-screen prompts to finish the reconfiguration process. 4. Ecobee turn fan on, As I knew, the Ecobee fan takes control of the HVAC system, including the fan. I found a source for my problem, and I found only limited answers. That is why I wanted to do a little research and bring more information for Ecobee users. ... If you choose auto, Ecobee will turn off the HVAC system after running the fan for 30 to 45 seconds. You ..., If your fan is running all day, it eventually starts to feel like cold air is blowing, whether or not you have the heat on. You can check the fan mode by going to Ecobee’s Comfort Settings. Go to Main Menu > Comfort Settings. From here, you have the option to set the fan to “Auto” or “On” in both heat and cool mode., Dec 16, 2020 ... Ecobee3 Lite: https://amzn.to/2WosWVY Ecobee Room Sensors: https://amzn.to/38e8Ing Favorite Smart Home Devices: ..., ecobee thermostat compatibilityWorks with the following ecobee thermostats with firmware version 4.6.3* or later:• ecobee SmartThermostat with voice control•..., It defeats the purpose of your HVAC system if the fan does not run when those system are called upon to run. The setting to run the fan X mins/hr is to run the fan a certain number of minutes per hour whether the A/C or Heat is called or not. The purpose is to recirculate the air in you home in an attempt to even out hot and cold spots. , If Configure Staging is set to Automatically. When your thermostat's Configure Staging setting is set to Automatically, you can adjust the Aux Savings Optimization value to lower aux heat usage. 2°F / 1.1°C - sacrifice savings for comfort. 2°F / 1.1°C - sacrifice savings for comfort. 2.3°F / 1.3°C - sacrifice a bit of savings for comfort., When you manually adjust the temperature, your ecobee will go into a Hold mode. Your set schedule will be ignored until the hold is dismissed or expires. During a hold, a bubble displaying the Hold temperature and how long the hold is active for will appear on the home screen. Good to know:, It defeats the purpose of your HVAC system if the fan does not run when those system are called upon to run. The setting to run the fan X mins/hr is to run the fan a certain number of minutes per hour whether the A/C or Heat is called or not. The purpose is to recirculate the air in you home in an attempt to even out hot and cold spots., How to run fan on a schedule. Question. Hi all, Just switched to Ecobee from Nest and used to have my fan scheduled to run every hour for 30 minutes while I sleep. When I set up …, Thx! 3. Reply. grabermike. • 3 yr. ago. You can setup an ecobee custom comfort profile, set the fan from auto to on for the comfort profile, then have IFTTT call that custom comfort profile. This is what I have done in my ecobee/IFTTT setup up., ecobee4 Smart Thermostats can listen and respond to your voice thanks to built-in Amazon Alexa voice service. Watch this video to see how you can set up Alex..., 58. 8.6K views 2 years ago NEW YORK. ecobee thermostat compatibility Works with the following ecobee thermostats with firmware version 4.6.3* or later: • …, Cannot turn on Fan Only mode. Problem. My Ecobee4 can turn on the fan when heating but not when I select Quick Setting -> fan on. It says Fan on and holding but nothing happens. I saw some earlier posts saying you need a green wire which I have. I also checked all wire connections and they look good., Tap Home > Tap the Thermostat > tap the Toggle on the bottom right > Set fan hold, then tap on your desired Fan Hold time. Fan mode in Comfort Settings. The fan mode can be set for specific Comfort Settings. In the On mode, the fan will run constantly for the duration of the current Comfort Setting as long … See more, What is ecobee? ecobee is a thermostat that operates via smart technology to regulate …, Step 1: Check to see if the device is switched on and connected. One might not know that the heater (gas and electrical) has a power button. Ensure that the controller is switched on. Also, ensure the breaker that gives electricity to the heating unit is in the “On” condition within the electric board., ecobee thermostat compatibilityWorks with the following ecobee thermostats with firmware version 4.6.3* or later:• ecobee SmartThermostat with voice control•..., "Hey Google, turn off the <thermostat name> hold." "Ok Google, turn on the <thermostat name> schedule." Fan Control: "Ok Google, turn the <thermostat name> fan on." Note: If this returns an error, try "Ok Google, turn the <thermostat name> blower on." System Mode: "Ok Google, set the <thermostat name> to heat." , I just upgraded my Ecobee 3 thermostat to the latest Ecobee 5 and noticed this peculiar thing happening. Basically, with my current temperature setting on a Hold temperature (different from my regularly scheduled set point temperature) and I manually turn on the circulation fan, the thermostat overrides that Hold temperature and runs the thermostat based on the scheduled temperature instead., Ecobee Turns on Fan But Not Ac. If your ecobee is turned on but the fan isn’t running, there are a few possible causes. First, check to make sure that the fan switch on your thermostat is set to “On.” If it’s set to “Auto,” the fan will only run when the AC is actually cooling the air. Second, check your filter and make sure it’s ..., Answer: You can troubleshoot and fix your furnace by cleaning or replacing the air filter, checking the thermostat settings, inspecting the blower motor, clearing clogged air ducts, repairing the ignition system or flame sensor, and implementing prevention techniques like regular maintenance and proper insulation., Zendaya is not only a talented actress and singer but also a fashion icon who consistently turns heads with her impeccable style. From red carpet events to casual street style, she..., If your fan is running all day, it eventually starts to feel like cold air is blowing, whether or not you have the heat on. You can check the fan mode by going to Ecobee’s Comfort Settings. Go to Main Menu > Comfort Settings. From here, you have the option to set the fan to “Auto” or “On” in both heat and cool mode., With the growing popularity of online shopping, more and more people are turning to the internet for their grocery needs. If you’re a fan of M&S food and want to buy their products..., Tap on "Set Fan Hold". Select "Indefinitely" + OK. Your fan will now click on until you switch it off. Note: 2 ways to turn fan off: Turn the thermostat …, The Ecobee is wired as follows: W – White: W1 B – Blue: C G – Green: G R – Red: RC X – Black: W2 T – Brown: Outdoor Thermistor - Not plugged Y – Yellow: Y1 O – Orange: Changeover valve (cool) - O/B. That's where my problem starts; everything will turn on properly (heat, cool, fan) and everything will turn off properly EXCEPT the ..., To turn off an ecobee thermostat, press the power button located on the top right side of the device. This will turn off the display and most of the functions of the ecobee. To completely shut down the thermostat, you will need to unplug it from the wall outlet. If you are using a battery-operated ecobee, you can remove the batteries to turn it ... , jrv331. •. If you want your fan on all the time that is a different setting. It’s in the profile setting, turn the fan from auto to on and the fan will run 24/7. Reply. com2kid. •. But if I do that the furnace can't start because the furnace can't turn on if the fan is already running. (It's pressure sensor gets confused), Your ecobee not powering-on can definitely be a frustrating experience. To better assist you, it would be helpful to know how your previous thermostat was wired, how the wires are attached to the control board, and if you are using the PEK. Your willingness to seek help represents the best of the sub’s mantra, be patient and stay humble., We have a full guide on troubleshooting your ecobee thermostat if it doesn’t turn on the fan or AC. Why Does the Ecobee Thermostat Turn On the Fan But Not the AC? Conclusion. Ecobee thermostats work really well with a specific HVAC system. And this is why you must be careful when you install your thermostat — especially if you install a ... , Step 1: Check to see if the device is switched on and connected. One might not know that the heater (gas and electrical) has a power button. Ensure that the controller is switched on. Also, ensure the breaker that gives electricity to the heating unit is in the “On” condition within the electric board., Short Answer. To program your ecobee 3 lite, first install the ecobee app and create an account. Once your account is set up, connect the ecobee 3 lite to your home’s Wi-Fi network. Open the app and follow the instructions to connect the thermostat to your home. Once the thermostat is connected, you can program it to your desired settings., Configure the HEAT DISSIPATION setting to the amount of time you want your fan to run after your HVAC setup has turned itself off. Remember to let it run for at least 30 seconds to guarantee that the excess heat generated by your climate control unit is pushed out of the home rather than funneled into your living spaces.