Do ceiling fans have a reset button

The most common problems with ceiling fans are not spinning, not turning on/off, light issues, noise, loose parts, and remote control malfunctions. Troubleshooting includes ensuring power supply, checking wiring, balancing blades, tightening screws, and replacing faulty parts. Several of these issues can be addressed without a professional.

To activate the learning code, turn the power off to the fan, and turn it back on again. Within 30 seconds of the fan turning back on, hold the hi and low buttons on the remote at the same time. Hold these buttons for about five seconds, and the remote will start to blink. This means the sequence is successful.When it comes to cooling and improving air circulation in your home, ceiling fans are a popular and energy-efficient choice. However, not all ceiling fans are created equal, and ch...The ceiling fan must be installed in a location so that the blades are 300mm spacing from the tip of the blade to the nearest objects or walls. Secure the hanging bracket to the ceiling joist or structure that is capable of carrying a load of at least 30kg, with two long screws provided. Ensure at least 30mm of the screw is threaded into the ...Press and hold the fan speed up and fan speed down buttons for 5 seconds. The LED will light red, blink green and return to solid red, and the receiver will beep to indicate that Wi-Fi reset is successful. After the Wi-Fi resets, the fan will broadcast its service set indicator (SSID). If the above sequence doesn't work, bring your fan to a ...The key to knowing whether this may be the issue for you is if the ceiling fan ever turns on or off without you even touching a button. If you have an RF ceiling fan remote, the correct frequency needed may be displayed on the back of the remote control. If not, then the typical frequency range for RF ceiling fan remotes is between 300 and 440 Hz.Improper installation, including failing to secure the fan properly to the ceiling and using the wrong size or type of mounting bracket, can cause ceiling fans to fall. Overloading the fan by adding additional attachments or connecting it to a circuit that can't handle the power requirements can strain the motor and lead to the fan falling.If the above reset sequence did not work, bring your fan to a complete stop and try the following: Press the following button sequence on the remote: Whoosh, ...How to factory reset a DC motor (980013/980003) when paired to the wrong transmitter? STEP 1: Turn main power OFF to all Fans. STEP 2: Turn main power ON ONLY for THE FAN NEEDING CODE CORRECTION. STEP 3: Press and hold "0" button on remote (or wall control SET button) for 20 seconds (within 60 seconds of power being turned on).

Key Takeaways. If your harbor breeze ceiling fan remote is not working with your ceiling fan, the following can be the reasons behind it. Remote range and signal interference …1. Hold the ends of the white neutral wires together and apply a wire nut. 2. Hold the ends of the fan power wire (black) and fan light wire (blue) to the black supply wire, and apply a nut. 3. Join the remaining wires of the fan and the wiring coming from the switch. These are ground wires and are bare copper.Step 2: Disconnect the Power Source. Unplug the power source from the light and wait one minute before plugging it back in. This will reset most lights, but other models may require additional steps. Many LED lighting products have a dedicated reset button.Insert new batteries and try out the remote to see if this has fixed the problem. You might want to try the remote closer to the ceiling fan to ensure it is not just a weak signal. If it is a weak signal we will cover that fix soon. You might want to jump to that section below. After having tried replacing the batteries and ensuring the ceiling ...To reset your Harbor Breeze ceiling fan remote you need to turn the power off then on and then push the ‘reset’ button or ‘learn’ button under the back cover of the remote. Make sure you hold the reset button down until the light comes on and the ceiling fan speed goes to medium.Some reports say that you could reduce your bill by 10%, but it really depends on the temperature at which you keep your house, your home's insulation, what sort of fan you own, and other factors ...

Make wiring connections per FIG. 2. Push all connected wires back into the junction box and reinstall the canopy onto the mounting bracket. Manually set fan speed control to HIGH and set light to ON using the pull chains. NOTE: For the remote to function properly, the fan must be on HIGH speed and lights must be ON to use.Steps to Reverse a Minka Aire Ceiling Fan Using a Remote. Ensure the fan is turned off. Locate the reverse button on the remote control. It is usually labeled as "REV" or "Reverse". Press the reverse button while the fan is off. Turn the fan back on using the remote control.The reset button for a Dell laptop depends on the operating system. For Dell computers with Windows XP, it is the combination of Ctrl + F11. For Vista and Windows 7, it is F8. For ...Do not use with solid state ceiling fans. Electrical source and fan must be 115/120 volts, 60 Hz. Maximum fan motor amps: 1.00 and maximum light watts: 300 incandescent only. AB. Installing receiver in fan: 1. Remove ceiling fan canopy from the mounting bracket. 2. Disconnect existing wiring between ceiling fan and supply at electrical junction ...Wait a few minutes, then turn the power back on. Press and hold the fan’s power button for 10 seconds, then release. Press and hold the fan’s reverse button for 10 seconds, then release. Finally, press and …

Soundhound stocktwits.

This not only saves energy but also reduces utility costs. Ceiling fans also help to distribute conditioned air more evenly, eliminating hot and cold spots in a room. Lastly, ceiling fans can be used in reverse mode during colder months to push warm air downwards, improving heating efficiency. Advertisement.Learn how to reset your ceiling fan remote control in 1 minute with simple steps and tips. Find out how to change the frequency settings, pair the remote with the fan, and fix busted remotes. Follow the guide to fix your ceiling fan problem with ease.How do I reset my fan’s settings? I don’t see my fan. in the Big Ass Fans app. I don’t see my fan’s lights in the app. App Setup. How do I get my Big Ass Fan to work automatically? I have a new router, or my wi-fi network name or password has changed, and now I …Jun 19, 2023 · Follow these steps to sync the ceiling fan remote control: Press and hold the ‘power on/off’ button and the ‘fan speed’ button at the same time. Release both buttons when the led light on the remote control blinks twice. Within 30 seconds of releasing the buttons, press and release the ‘learn’ button on the ceiling fan’s receiver. You can tell that a ceiling fan capacitor is bad if the case is melted and burnt, or if the circuitry is frayed. Set a multimeter to OHMs, connect it to the capacitor's terminals, and look for low readings that indicate that it is bad. A bad capacitor can often point to other problems within the ceiling fan, and you may need to replace it ...To reset your ceiling fan remote, start by turning off the power to the fan at the main electrical panel. Then, remove the batteries from the remote and press all of its buttons to ensure there is no residual power. Next, reinstall the batteries and turn the power back on at the electrical panel.

Look for the switch. If your ceiling fan is reversible, then in most cases, there will be a toggle switch somewhere on the motor housing. It could be on the side of the fan assembly or it can be hidden within the light fitting, so you may have to remove the light shade to see it. Check the controls on the remote/wall switch.When using a ceiling fan for hot air circulation make sure to set the speed to low as a medium or high setting may create a breeze and create an unwanted cooling of the room. There are many reasons to make good use of your ceiling fan during the winter months. Those with high or vaulted ceilings will see a great temperature difference with the ...Ceiling fan direction winter = clockwise/updraft. When your fan is on and running in the proper direction, it also helps alleviate the extra work your AC unit is putting in. For instance, if you have your indoor temperature set to 75 degrees, you can turn on your living room fan and drop the temperature in the fan's room ato 71-72 degrees.A ceiling fan fall can be lethal if it falls directly upon the head of a person. An average ceiling fan can weigh somewhere around 10 to 50 pounds, varying on the fan's type and size. The motor is the heaviest part of a ceiling fan. It sits right in the center and is surrounded by lightweight blades. Assuming that the heavy motor drops on a ...Oct 9, 2023 · On your remote, press and hold down both the fan speed and light buttons together for five seconds. The LED on the remote should begin to flash. Release both the fan speed and light buttons. Press the button that corresponds to the desired function (e.g., high, low, or medium fan speeds; dimmer switch). This remote controller is designed to separately control your ceiling fan speed and light brightness. There are four buttons (HI, MED, LOW, OFF) to control the speed of the fan and off. The light dimmer button will control the light brightness dimmer and off. The red indicator on the transmitter will light when one of the five buttons is pressed.The more space between the ceiling and the blades, the better for airflow and circulation. Ideally, aim for at least 12 inches. Low Ceilings: For rooms with ceilings 8 feet or shorter, flushmount "hugger" fans are the ideal option. As the name suggests, these fans "hug" the ceiling to create a low profile.Aug 18, 2019 · If the remote is sending a signal, but the fan is not responding to it, you may need to change the dipswitches. If the fan sometimes turns on by itself, off by itself, or the light kit does this on it’s own, then this is a good sign you do need to change the dipswitches. Dipswitches are toggle switches on the back of the remote. In case you cannot find any holes on top of the fan, you are most likely dealing with a self-lubricating model. If so, you will have to take the fan down and dismantle it to reach the motor and oil it manually. 5. Check the Oil Level. When you locate the oil hole, you have to check how much oil is left in the fan.Wiring and Connections: Faulty or damaged wiring and connections can also cause a ceiling fan to not respond to the remote control. If you are comfortable with electrical work, you can inspect the wiring and connections for any visible issues, such as loose or frayed wires, and repair or replace them as needed.A 20-amp breaker can only carry loads up to 80% of its maximum current rating. This means it should only handle 16 amps. To give an estimate, a 20-amp breaker can support up to 19 units of 72" ceiling fans (assuming their current draw will be at 0.83 amps per fan); that many fans will demand a total of 15.77 amps.A ceiling fan can help distribute the cool air that the AC unit produces, meaning the unit has to run less. A ceiling fan cannot, however, lower the actual temperature in a room without an air conditioner. This is a somewhat complicated topic with a lot of incorrect information, which is why we've compiled this guide.

There are several ways to reset a ceiling fan remote, but here’s the most straightforward: Hold the button down while the power is off until the remote’s light starts to flash. Then, press and hold it again for 15-30 seconds to resynchronize the remote with your fan.

If your remote doesn't have a specific 'reset' button, the 'fan off' button or the 'high,' 'medium,' and 'low' buttons can often be used for this purpose. Step 2: Press and hold the 'reset' button (or the appropriate buttons) for about 3-5 seconds. 8. How to reset a Minka Aire ceiling fan remote. You can reset or reprogram the ceiling fan remote using the following steps: Remove the covering of your remote control to expose the battery. Take note of the two sets of four buttons on the back of the remote. Remove the battery. Step 2: Testing the Fan's Oil Level. To test your fan's oil level, you'll need to use a pipe cleaner. Bend it into a "J" shape, making sure that the short end is about ½" long. You'll then turn the pipe cleaner so that the bend is facing upwards, like a candy cane. Insert the short, ½" section into the oil hole, then remove it.The fan base must be securely mounted and capable of reliably supporting at least 35 lbs. See page 5 of owner’s manual for 5. Follow the recommended instructions for the proper method of wiring your ceiling fan. If you do not have adequate electrical knowledge or experience, have your fan installed by licensed electrician. support requirements.Jan 3, 2021 · https://hamptonlightingadvice.com/harbor-breeze-ceiling-fan-remote-not-working/ In this video we show you where you can find the 'Learn' otherwise known as R... Jul 12, 2016 ... This video will show you all about fixing a common problem with ceiling fan remote controls. A few important notes: - The setting in the ...Step 2: Restart a Gas Furnace With the Reset Button. Make sure the pilot light is out. If it isn't, turn the gas control switch to "off" and make sure that the pilot goes out. Then, turn down the thermostat to its lowest setting. If the furnace has an electronic ignition, turn off the power by turning off the circuit breaker that controls the ...the ceiling fan motor. Refer to Figure 2. Do not modify or damage the antenna wire, as control performance may be reduced. After securing the receiver, antenna, and wiring, finish hanging the ceiling fan according to its instructions. Fan Installation Types: NOTE: Some fans may have considerable excess lead wire. For easierRemove the wires from the damaged switch and connect them to the corresponding terminals of the new switch. Place the new switch into the electrical box and screw the cover plate back in place. Turn ON the power and check whether the switch is working. 2. Reconnect the loose wiring on the ceiling fan.Honeywell Ceiling Fans Xerxes Ceiling Fan. Now 15% Off. $238 at Amazon $202 at Overstock $258 at Walmart. Credit: honeywell. At 62 inches in diameter, this ceiling fan with eight reversible blades ...

Michael monroe net worth.

Power outage sheridan wy.

Fan Light Kit is Not Working. Ceiling Fan is Turning On/Off. Ceiling Fan has Airflow Issues. Ceiling Fan is Not Reversing. Ceiling Fan is Wobbling. Ceiling Fan is Noisy. Ceiling Fan Is Not Working.To reset the Lennox AC unit and improve its performance, you need to follow several steps: Start the mold block of the internal regulator. Look for an electrical circuit switch on the device that feeds the air conditioner itself. Press the switch and wait half a minute. After it needs to be launched again.Yet there's another thing I must mention. A ceiling fan can also not do the same job as a window fan. With a window fan, it pulls cool air through the fan and into the room while also helping hot air to move out of the room. This does actually help reduce the overall temperature in the room. A ceiling fan does not do that.Craftmade 52″ Targas Ceiling Fan Manual. Read More. Craftmade 52″ Tempo Ceiling Fan Manual. Read More. Craftmade 52″ Tempo Hugger Ceiling Fan Manual. Read More. Craftmade 52″ Universal Hugger Ceiling Fan Manual. Read More. Craftmade American Tradition Ceiling Fan Manual.Solution. #2. The fans won't be the cause of your PC turning off (unless you have all fans connected to the controller and don't have something on your CPU_Fan header on the board - that might do it). …Factory Reset and Power Cycle Ceiling Fan Smart Switches ... Factory Reset. Press and hold the power button on the circle switch until the LED light turns red, then let go. The light indicator will blink blue once it is successfully reset. Power Cycle. Pull out the airgap to power cycle the Ceiling Fan Smart Switch.If you are wondering whether ceiling fans are outdated, the answer is no. Ceiling fans are not outdated, they are very popular even today. In addition to looking good in any room, they also help to reduce air conditioning costs. So ceiling fans are still in demand today, and they will be so for the foreseeable future. Table of Contents.Fanimation ceiling fans have been utilized in a wide variety of venues ranging from residential homes to world renowned theme parks. Fanimation has graced the silver screen in the movie I,Robot been featured on HGTV and also made an appearance on Extreme Makeover Home Addition .Here's what you want to know. Ceiling fans can be controlled by; 1. Pull cord 2. Wall switch 3. Remote 4. Smart controller. For most people, the wall switch is the best option since it works well and is reliable. Remote controls are a good options that provide extra comfort at the expense of reliability.Turn off your ceiling fan using the remote (if the power button is working). Press the off button on the fan for about 10 seconds then release it. Wait for about another 20 seconds and then turn the fan on again (using the remote). Following the above-mentioned steps, you should be able to reset your Fanimation Slinger V2 remote without any issues....remove the batteries from the remote then plug the fan back in and, reinstall the batteries; this resets the fan ... ….

Oct 27, 2019 ... My spring didn't have enough strength so when I winded it up and pulled it would make a click noise, but wouldn't pull back. ... You may have to ...This remote controller is designed to separately control your ceiling fan speed and light brightness. There are four buttons (HI, MED, LOW, OFF) to control the speed of the fan and off. The light dimmer button will control the light brightness dimmer and off. The red indicator on the transmitter will light when one of the five buttons is pressed.To reset your Harbor Breeze ceiling fan remote you need to turn the power off then on and then push the 'reset' button or 'learn' button under the back cover of the remote. Make sure you hold the reset button down until the light comes on and the ceiling fan speed goes to medium.Remove the wires from the damaged switch and connect them to the corresponding terminals of the new switch. Place the new switch into the electrical box and screw the cover plate back in place. Turn ON the power and check whether the switch is working. 2. Reconnect the loose wiring on the ceiling fan.The Universal Ceiling Fan Wall Control is a completely universal ceiling fan control that works on Hampton Bay, Hunter, and Casablanca fans as well as many other. This wall control provides a simple solution control fans speed and the fan light while keeping a very nice flush looking design. The wall control is simple to install and easy to use.First, check to make sure that the power is turned on at the circuit breaker. If the power is off, flip the breaker switch to the on position and see if the fan starts working. If the power is on and the fan still isn't working, it's likely that a fuse has blown or there is a loose wire. Check the fuse box and replace any blown fuses.Do you have a ceiling fan that all of a sudden is not blowing air anymore, you do not have a button on your remote that will reverse it, and there is no swit...Shut off the power to the fan for at least three minutes. Turn back on the power. Within 20 seconds of turning the power on, press 3,2,1 on the remote in the same order. If you are using the Advan-Touch fan, repeat the steps above but ensure to press and hold the down and up arrows simultaneously.My Hunter ceiling fan (model #25560) and its lights no longer work when I pull the pull-chains. The fan/lights are NOT controlled by a wall switch nor by a remote-control. The wiring between the fan and the electrical panel is OK and all of the circuit breakers are On. Does the fan have a reset button? If so, where is it?2) Next, press and hold the "learn" button on your remote control. 3) Then, enter the code for your ceiling fan into the remote control. 4) Finally, press the "learn" button again to complete the process. That's it! You have now successfully programmed your Minka Aire ceiling fan remote. Back to top. Do ceiling fans have a reset button, In this video I show you how to reset your minkaAire ceiling fan. This is useful when your neighbors are turning on and off your fan for you. Re configure ..., To connect an Arlec ceiling fan to your new remote, turn on the fan using the wall switch. Then, press and hold the power button until a beep sounds. Ensure you have working and properly installed batteries in the remote when carrying out this step. 4. Fan wobbles when spinning., Do not use with solid state ceiling fans. 3. Th e decorativ g (canopy) t the ceiling must e metal. The metal housing acts as a protective cover for the Control Unit. DO NOT USE WITH A NON-METALLIC HOUSING. 4. Only the remote unit should be used to change fan speeds. Do not use the pull 8.chain to change fan speeds after installation., Do ceiling fans have a reset button? There are several ways to reset a ceiling fan remote, but here’s the most straightforward: With the power off, hold down the button until the light on the remote flashes. Then, press and hold it again for 15-30 seconds to resynchronize the remote with your fan. Why did my Hunter fan stopped working?, Turn on the fan and press the learn/reset button. Hold the learn/reset button until the light of the fan comes on and the fan goes to the medium spin cycle. If your fan and remote are of older models and have dipswitch settings, then you will need to select the similar dipswitch settings on your remote as on the fan., Universal 3.5-in 3-Speed Black Plastic Indoor Ceiling Fan Remote. Hunter. Universal 1.38-in 3-Speed Dove Grey Plastic Indoor Ceiling Fan Remote. Shop the Collection. Hunter. Universal 2.95-in 3-Speed White Plastic Indoor Ceiling Fan Remote. Harbor Breeze. Universal 4.72-in 3-Speed White Plastic Indoor Ceiling Fan Remote., Reset button pops out whenever you turn on an appliance plugged into the outlet. Each of these symptoms can indicate a larger issue with your ground fault interrupter. You may have a defective GFCI, insufficient current, or have a GFCI that's wired incorrectly. Consult with a trusted electrician to understand what options may be available., Download Article. 1. Locate your circuit breaker box if the fan doesn't turn on. Pull the chain on your fan and flip the wall switch to turn your fan on. If nothing happens, it could be because the circuit to the fan has been tripped. In this case, you'll need to check the switches in your breaker box., Power surge may have cleared memory and remote and re-syncing did not resolve the issue. FACTORY RESET OF REMOTE: Turn the power to the fan off for 3 seconds, then turn the power back on for 3 seconds. Repeat this 5 times. The light will blink to confirm the reset was successful. The LED indicator on the remote does not illuminate., If your fan is not spinning, there are a few things you can check. First, make sure the fan is receiving power by checking the circuit breaker or fuse box. If the power is on, ensure the fan is properly connected to the power source. Additionally, check the fan blades to ensure they are not obstructed by dirt or debris., If you determine that your wall switch is not the source of the problem, you can then move on to examining the ceiling fan. Make sure the power to the fan is turned off at the circuit breaker and wall switch before starting. 04. Take the canopy cover off the fan so you can see the fan’s wiring. 05., Many ceiling fan remotes come equipped with a reset button located on the back of the remote. This method is straightforward and often effective. Turn off the ceiling fan using either the remote control or the wall switch. Locate the reset button on the back of the remote. It could be a small round or square button., Key Takeaways. If your harbor breeze ceiling fan remote is not working with your ceiling fan, the following can be the reasons behind it. Remote range and signal interference …, Start by testing out the wall switch. 01. Test the circuit breaker first by flipping it off and then back on at the electrical box before testing your ceiling fan. If it still isn't working, move onto the wall switch that's used to operate the fan and try flipping it off and on. 02., If you have a switch on your fan that is supposed to reverse the fan, then the problem is likely that the switch on the fan is bad and needs replaced. To get the switch contact the store you bought it from or the company that makes the fans and ask about it. Once you get the new switch all you have to do is dissemble the fan and remove the old ..., The pros of bladeless ceiling fans are that they are safer, quieter, and more energy-efficient, circulate the air better, and don't accumulate much dust compared to conventional fans. The cons are that they do make some noise, are more expensive, and may have to be installed by a technician. Bladeless fans sometimes called "air multipliers ..., Do you have a ceiling fan that all of a sudden is not blowing air anymore, you do not have a button on your remote that will reverse it, and there is no swit..., To successfully reset the Hampton Bay Ceiling Fan remote, simply press and hold the reset button for a few seconds. The reset button is located on the back of the remote, usually near the battery compartment. It's a small, recessed button that may require a pen or paperclip to access. Advertisement., 5 days ago · Another feature it does not have is the reverse blades button, which is semi-important to me during the winter months. If this is not an issue for you then this is a good replacement remote control. This ceiling fan remote has 4.2 stars out of 5 stars. 4. Wink Enabled Universal Ceiling Fan Premier Remote Control , 2. Disconnect the Wiring. Carefully disconnect the wires from the fan motor. Use electrical tape to mark the corresponding wires for easy reconnection. 3. Remove the Mount. Unscrew the bolts holding the fan mount to the ceiling box. Lower the fan carefully and place it on a flat surface. 4., Step 7: Release The "Fan" Button. After inserting the batteries, release the "Fan" button. This will complete the reset process and should allow the remote to connect to the fan. The LED light on the remote should blink or light up to indicate that the remote has successfully paired with the fan., Most ceiling fan remotes have a reset button – just press and hold that for about five seconds, then release it. This process resets the remote, and hopefully, it starts functioning normally again. Lastly, the issue could be with the fan’s receiver, a device installed inside the fan’s motor housing., The experts at FanDiego teach you how to reset and fix a Casablanca W-505 ceiling fan remote control.http://www.fandiego.com, seconds. You must press the "SET" button within 30 seconds of restoring power to the fan. 3) When press the "SET" button the fan will make one musical sound and start to run to begin the control setting process. 4) DO NOT press any button(s) after pressing the SET button and while the fan is programming or it will fail to program., Access receiver unit. Check if the dip switch settings on the remote and the receiver match. Sync the remote and receiver: turn the power back on, press and hold the “Sync” button, and watch for a response from the fan. It might beep, the lights may flash, or the fan blades might move slightly., 112. 2. If the fan has pull-chain switch control of speed, make sure the pull switch is in the highest setting. This is reqd to allow the remote to control the speed. To test if the remote transmitter/receiver is at fault, disconnect the receiver and connect the wires directly as if you have no remote., How to reset a Hunter ceiling fan. If you want to reset a Hunter ceiling fan: Press and hold the power button on your remote for about five seconds. Wait for LED lights to blink. Wait for 30 seconds after the blink and press any button. You will hear a beeping sound, and the lights will blink continuously. Once the LED stops blinking, you will ..., About This Product. The Universal Smart 4-speed ceiling fan remote control adds new functionality to your ceiling fan. This remote converts your standard ceiling fan into a Smart ceiling fan making it compatible with Google Assistant, Samsung SmartThings, or Alexa and allows you to control your ceiling fan from anywhere via your smart device (smart phone, tablet, etc.)., Here’s how to reset Daikin air conditioner remote: Find the on/off switch on the AC’s remote. Press the button for 2 seconds and release it. Press the switch once and then a second time to restart the AC. Wait for the AC to restart to …, Receiver Box. Remote-controlled ceiling fans come with a receiver box and remote which are set to the same frequency. This allows the two of them to communicate so that you can control your fan as you please. However, if you have several ceiling fans of the same type in your home, you'll want to be sure that switches in your remote are paired ..., You can tell if your ceiling fan uses a single or dual capacitor by checking the microfarad rating and the wiring terminals on the capacitor. A single capacitor will have one microfarad rating and two sets of terminals, while a dual capacitor will have two microfarad ratings and three sets of terminals. Always remember to turn off the power ..., Locate and then pull the fan cord attached to your fan. Pull the fan cord once to turn the fan on high. Pull it twice to turn the fan on medium; three times to turn the fan on low, and a fourth time to turn the fan off. If you're looking for a long-term solution, fix or replace your fan's remote control., Jan 26, 2023 · The newer remotes and fans have an easier way to do this instead of frequency sliders or dipswitches. If you set the dipswitch to 1 and press the ‘Learn’ button in the remote with a paperclip or a pin, then the remote-control unit will find a unique code just for this remote and the ceiling fan that is nearby.